How to Connect a Bathroom Sink Drain

| | 0 Comments

If you do not intend on giving away, reselling, or aren’t simply moving your hot tub, the best way to go about removing a hot tub is simply to take a sawzall to it. It is safe to say, however, that the process is a little more complicated in nature than simply sawing the spa into bite-sized pieces. Here is a guide to removing a hot tub that you are no longer interested in. Step 1 – Reread Instruction Manual Re-read the manufacturer’s instructions for the hot tub to remind yourself of all of the aspects of the spa’s original construction. You need to have a decent idea of what electrical elements are involved, how the heater is hooked up, how the gas lines work, and so on. Immersing yourself in these details will make sure that you are safe and protected when you are disassembling your spa for removal from your properly. Step 2 – Unplug Electrical Wiring Now you are going to want to unplug all of the electrical hook-ups including the gas line, electricity, and the heater. Make sure that all of this electrical equipment is properly removed.

Ask the Builder | How to avoid problems when replacing a bathtub

Fortunately, if caught early you can clear a clogged drain using common household items. Vinegar, baking soda, borax, and lots of hot water are simple, yet effective tools in clearing slow-draining sinks. Steps Preparing the Drain Mixture 1 Drain any water from the sink or tub. If it’s really slow-draining, this may take a while, but if you remove the water, you drain-clearing mixture will be able to work on the clog much faster.

You have several options for creating a non-commercial drain opener. Most involve vinegar and another substance that create a chemical reaction when combined.

You may even want to extend the drain hook up closer to the edge of the unit for easier connection. These repairs only require the correct couplings and a can of cement. It is not a bad idea to carry spare couplings, tubing, and glue along with you on your trips, just in case.

Instead of retaining water in them at all times, toilets in campers use a trapdoor-type slide plus a water flush component to dispose of the waste. The water connection to the toilet is no different than used at home. One of the most common problems with the toilet is incomplete closing of the sliding trap door. When operating correctly, the slide fits snugly into a groove.

After a period of time, bits of toilet paper may become lodged in the groove preventing the slide from closing tightly. This will allow air to seep from the waste holding tank, causing an odor problem. Carefully clean this groove with a small piece of wire until the slide seats properly into the groove. Size Doesn’t Matter RV Plumbing Repairs Are Usually Simple Another common problem with an RV waste system is the short life of the rubber seals contained in the outside valves that lead from both the gray-water and black-water holding tanks.

These seals are merely rubber o-rings which fit tightly around the slide valve rods. These need changing at least every three years because of their exposure to chemicals in the gray or black water tanks.

How Do You A Join Cast Iron Pipe to Plastic Drain Pipe In Your Home

Pop-ups are simple mechanical devices that use a system of links and levers to move a drain stoppers up and down to seal a sink bowl or bathtub. How a Pop-Up Stopper Works Pop-ups are simple mechanical devices that use a system of links and levers to move a drain stoppers up and down to seal a sink bowl or bathtub. Bathroom sink pop-ups are raised and lowered with a lift knob or lever, usually located on or near the faucet body. This rod pushes the stopper up or lets it drop down into the drain body.

The lever operates a lift linkage that pulls on a spring.

If you’ve got a water sitting in the bottom of your dishwasher, the first thing you want to do is check the drain plugs for blockage in the dishwasher pan. Large chunks of food and other items may.

The bathtub should be installed and put in place in the bathroom. After doing this, the drain rim should be put under the drain hole. It should be held firmly for some time. Fix Gasket and Nuts The rubber gasket on the bathtub should be put on the part that hooks to the tub. Slide the nut and washer onto the overflow pipe as well as the drain shoe. A drain T-fitting needs to be put on the overflow pipe. Connect the drain and overflow pipes to the drain T-fitting. Tighten the nuts with pliers.

While doing this, care should be taken that too much pressure is not applied. Connect the Trap A drain T-fitting needs to be put on the overflow pipe.

How to Replace a Drain Assembly on a Claw Foot Tub

Tube Stuff Suppliers Appendix B. Tube amps have always been the amplifier of choice for the working musician. Musical myth has ascribed almost magical tone to them. While the results may not be entirely magic, tubes do have a sound that is different from solid state amplifiers, and one that happens to make amplified music sound better to the human ears and brain.

There are lots of technical and psuedo-technical explanations for why this should be true, but there is enough solid evidence that it is a real effect to trust it. The real reason to use tube amps is simply that they sound better.

Nov 09,  · Here’s how to replace a tub drain and install a new stopper. After years of use, the plastic-and-metal pop-up stoppers on two of our tubs shattered.

Other, gentler methods of drain cleaning can remove clogs of hair, dirt, and grease without posing risk to your pipes. Many of these affordable methods use common household items and do not require an extra trip to the store for supplies or a call to the plumber. Straighten the body of a wire coat hanger and modify the hook, if necessary, so that it fits down your drain. Then elongate a large paperclip. You should now have two straight tools that can fit into the shower drain opening. Put on rubber household gloves and remove the drain strainer, if possible, for easier access to the drain opening.

Pick up any loose hair from the top of the shower drain strainer and opening with your fingers. Run water until about four inches fill the tub and the clogged drain begins to empty slowly. Take a plunger and plunge the shower drain to bring the hair closer to the top of the drain.

RV and Camper-Trailer Plumbing Repairs and Maintenance

A tub is large and heavy and bathrooms may be awkward in shape and are not usually all that large, which can make removing an old tub and installing a new one a real challenge. However, bathtubs can get worn over time and need replacing. You will need help for this project to move the tub. Steps Measuring the Bathroom Space 1 Ensure the new bathtub will fit in the space.

Here is a tub drain pipe and partial vent system. This is what the average bathtub drain and vent system looks like if you could remove the drywall or plaster from your walls. The plastic pipe connected to the tub is the overflow pipe. The chrome fitting up high on the inside of your tub is the overflow. Water enters it and flows down into the pipe.

Check Prices On Amazon Ideally, professionals install the drum trap in a place with easy access. This way, you can remove the cover to clean. In other cases, people have it hard to remove the cover which fused together by time. Therefore, when drum traps stop, they are extremely difficult to clear by rodding. Drum traps existed so that people could find jewelry or valuables if lost down the drain. The trap would catch and guard the ring or earring by sinking to the bottom.

The likelihood that a valuable would flow into the waste opening at the top of the trap is highly unlikely. A sand trap also helps to separate sand and oxidized organics found in water supplies. What Is a Building Trap? Back in the day, before people used or understood system venting, vermin like rats or insects could move freely from building to building, house to house.

Not to mention the sewer gas odor could be unbearable because of back pressure and trap siphonage.

All About Plumbing Traps

The photo below shows a nice example of a house with long downspout extensions carrying water a good distance away from the house. While the setup above is great for the house, some people prefer not to have the downspout extensions so visible. Dealing with the walkway can also be an issue; the easy options are to create a trip hazard by running the downspout across the walkway, or a slip hazard by stopping the downspout short of the walkway, which will make for an icy mess in the winter.

This tubing gets buried in the yard and eventually terminates at a lower point, allowing water to drain away from the building. This is the same stuff that I mentioned in a recent blog post while discussing sump pumps discharging to a yard drain. Just like the discharge tubing from a sump pump, connecting a downspout directly into an underground drain can allow for ice to back up.

Install the stopper assembly on the tub, then assemble the lower drain extension. Place the drain extension into the hole in the floor, move tub into position and align over the extension drain (Image 2).

The truth is, there are so many side track issues, exaggerations and outright misinformation perpetuated by manufacturers and retailers alike that even an intelligent, diligent researcher does not have a hope in hell of making an educated buying decision. For the most part, they are just regurgitating the pitch they got when they bought the line of spas they are selling. The Stuff that really matters The Dealer: Ok first is the Dealer… Trust me here folks… A good industry person with 20 years under their belt who has been under the spas fixing them, selling them and designing them will have made a good choice on the line of spas he carries.

Now I will only say this a million times so listen close… components, components, components, components, components, components, components, components, components, components, components, components, components, components… In case you missed that people, it is all about the components!!! When we build a hot tub we can buy good solid proven track record components like Balboa heating and control systems, and Waterways jets, pumps, and fittings or we can buy inexpensive components like Rising Dragon jets, controls and filters… And there are also a whole pile of guys in the middle.

The idea is silly… All they do is have someone build the parts for them and then private label it. If they are using cheap Chinese knock offs then they will talk about the side track issues, like shells, bases, and frames. In some instances even claim they build their own parts… Shells: The pitch is that the overall cost of buying the product is going to be reduced by not haveing to properly prepare the ground… Folks this is just bad advice.

If you drop a tub on the ground you will have to lift it in a few years and re-level it… Do it right the first time… no matter what the sales guy says put a patio stone base down and avoid the many issues that come with bad ground prep.

How to Replace a Drain Assembly on a Claw Foot Tub

How to navigate your way through the minefield that is plumbing code. Building code intro These snippets come from the IRC rules, but note that building codes vary in different local areas so you will need to do your own checking up on codes in your area. Also, this is just a few of the building codes that caught my eye and appeared relevant to my case.

Hooking up a washing machine and dryer is a fairly straightforward task. Although many vendors offer installation services, installing these appliances yourself can save time and money. Different models of washers and dryers do vary somewhat, but these instructions will guide you though the process.

The links and mentions on this site may be affiliate links. But they do not affect the actual opinions and recommendations of the authors. Wise Bread is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon. Money Beagle 1 I bought a small plunger designed for sinks the typical one would have been too big to create a seal and it’s kind of gross to use one that you’d used in the toilet anyways , and that worked like a charm to unclog a drain that had been giving me fits since we moved in.

I had tried many of the suggestions you listed as well as Drano and the standard fare. All provided temporary relief but it was the plunger which really did the trick. The plunger ‘brought up’ some particularly vile contents into the sink so be prepared to clean up. Using the plunger loosened up contents which not only backed up into the sink but also into the area that provides the overflow drain. You’ll want to flush this with boiling water immediately to rinse the loosened up matter down.

Still, it worked like a charm and draining a half-full basin went from a two minute process to roughly four seconds. I spent 4 seconds on it like you and fixed the issue after messing with it with a coat hanger for 15 minutes. Pamela 3 All good tips.

Hot Tub Buyers Guide

I’m sure this is not optimal set up but will it do? I don’t mind dropping water in the line once in a while. I don’t think it’s allowed by code either.

A rough-in plumbing diagram is a sketch for all the plumbing pipes, pipe fittings, drains and vent piping. This is very important as the new branch line you install must connect to an existing plumbing drain in the right location. Sign up to my newsletter to receive expert advice for your home!

I have a set of thin needle nose pliers – got it as a set for building my pc s and the longest one is fairly thin. Long assed hemostats with a curved tip are exactly what I use to clean tub drains on a daily basis at the unit apt complex I maintain. Get them at any Harbor Freight store! I hadn’t counted on the small holes in the strainer making this so hard. I couldn’t get a coat hanger with a hook down the strainer so I fashioned an L-shaped wire. I was able to grab onto the gunk and get it to the top of the drain, but I had nothing thin enough to get through the drain holes to get the gunk out.

I was able to fashion a “lift bar” to get the gunk to the bottom of the strainer and then used another hanger wire to try to get parts of it to stick out of a drainer hole a little bit. Then I used my needle-nose pliers to pull out the gunk, piece by piece. It was a loooooong process, but I think it worked. I used the hand sprayer and jetted some hot water down the drain to try to wash down any stray pieces that I couldn’t get out.

The drain seemed to run okay, with no back-up into the shower. I have no one to blame but myself, my husband is practically bald and I have shoulder-length hair, so it was my hair that I had to fish out. Unfortunately, my husband is disabled so I couldn’t make him do this dirty work which means that I’ll be sure to use a plastic hair catcher on top of the drain to minimize the hair build-up. I don’t want to do this again anytime soon!

how to replace a bathtub drain


Hello! Would you like find a sex partner? It is easy! Click here, registration is free!